Mũi taro ren tay (tạo ren trong) Rougher DIN 2181 HSS-G - M 14 x 1.25
You use this Mũi taro ren tay (tạo ren trong) for controlled internal threading by hand, for example in repair work, fitting, and small batch production.
Selection depends on thread designation, hole type, work material, and how you clamp and guide the tool. M denotes ISO metric thread designation used for common metric screw threads in machine building and maintenance. HSS-G indicates a ground high speed thép tool, typically selected when edge definition and repeatability matter.
- Produce clean ren trong when you need a controlled fit for screws and studs.
- Process: manual driving or assisted driving depending on your holder and machine setup
- Use: cắt ren, taro lại ren, and làm sạch ren depending on condition
- Clean chips from the tool and hole regularly to reduce torque peaks and edge chipping.
Lưu ý Align the tool to the hole axis and avoid forcing, since torque spikes can damage the thread flanks.
- Supports consistent internal threading when alignment is correct
- Usable across common workshop and maintenance processes
- Helps reduce rework through repeatable tool geometry
- Allows controlled fit when you choose the correct thread designation
- Helps keep thread quality stable when you use appropriate lubrication
Hạn chế
- Not suitable for every work material without correct cutting fluid and stable alignment
- Not intended for high performance production cycles without validated process parameters
- Prepare the hole and remove burrs so the tool starts straight.
- Clamp the workpiece securely and align the tool to the hole axis.
- Use a suitable holder or drive and apply cutting fluid for the work material.
- Start the thread with controlled feed and keep the tool guided through the first turns.
- Continue with steady torque and clear chips from the cutting area as needed.
- Reverse to remove the tool, then clean the thread and the tool flutes.
- Check the thread with the intended fastener or a suitable gauge and protect the part.
- 1 chiếc Mũi taro ren tay (tạo ren trong) Rougher DIN 2181 HSS-G - M 14 x 1.25
- Product type: Mũi taro ren tay (tạo ren trong)
- Standard: DIN 2181
- Thread designation: M
- Tool material: HSS-G
- How do you select the correct thread designation for this product
- Match the thread designation in the product name to the mating fastener or component standard, then confirm that your workpiece material and process setup suit the tool type. If you work with mixed standards, separate your tooling by thread family to avoid mix ups.
- What holder or drive concept do you need
- Use a holder that clamps the tool concentrically and supports straight alignment to the workpiece axis. For manual work, choose a stable hand drive that lets you feel torque changes. For machine use, verify reverse capability and consistent feed.
- Where do you find more technical information for this tool type
- Technical information Mũi taro ren tay (tạo ren trong) as PDF
- Which hole preparation checks matter most
- Prepare the entry edge, remove burrs, and keep the hole clean so the tool starts straight. In lỗ bít, confirm that there is enough depth for the tool lead and chip space. In lỗ thông, support chip evacuation out of the exit side.
- How do you reduce the risk of misalignment
- Start the tool with the axis visually aligned, then guide it through the first turns with low torque. Use stable workholding and avoid side load. If a thread feels tight early, remove the tool, clean chips, and inspect the entry.
- Can you use this in repair work
- Yes, for many workshop repairs you can use the tool to restore a usable thread when the base material is still intact. Clean damage first and avoid forcing, since distorted threads can increase torque and edge wear. For heavily stripped threads, a sửa ren insert system can be the better option.
- Where can you find the full VÖLKEL catalog section for this product family
- VD 23 catalog as PDF
Do you need help selecting or using the product?
Use the biểu mẫu liên hệ.
