Cặp mũi khoan taro STANDARD M 6 x 1.0, DIN 371, HSS-E

Name: Cặp mũi khoan taro STANDARD M 6 x 1.0, DIN 371, HSS-E
Brand: VOLKEL
SKU: 37793
Price: 362000.0 VND
Availability: OutOfStock

★ 0.0 (0 đánh giá)

Đã bán: 0

Nhập khẩu từ: Đức

Xuất xứ: Đức

Cặp mũi khoan taro STANDARD M 6 x 1.0, DIN 371, HSS-E VÖLKEL, mã 37793, dùng cho gia công ren trong.

SKU: 37793

362.000 đ

Giá đã bao gồm VAT

Vui lòng liên hệ để được báo giá và tình trạng hàng.

Mô tả

Cặp mũi khoan taro STANDARD M 6 x 1.0, DIN 371, HSS-E

Plan the operation with suitable cutting fluid and a stable holder so the tap enters straight and the chips can evacuate without jamming.

Ứng dụng

Use the set when you want a matched drill and tap pairing for a defined thread designation.
Use for ISO metric threads as designated in the product name.
Use for lỗ bít or lỗ thông based on lead form and flute geometry.
Use a drilling and tapping setup that keeps both tools square to the surface.
Process: manual driving or assisted driving depending on your holder and machine setup
Use: cắt ren, taro lại ren, and làm sạch ren depending on condition

Lưu ý Verify the exact designation and ring execution in the product name before use. VÖLKEL uses and recommends spiral drills from LÖHER. LÖHER product catalog as PDF

Lợi ích

Clear assignment to ISO metric threads through the designation in the product name.
Efficient chip transport supported by flute design when correct cutting fluid is used.
Suitable for repeatable workflows in maintenance and serial production setups.
Simple inspection using a suitable screw or gauge after cleaning the thread.
Consistent ren trong geometry when the tool is guided square to the surface.

Hạn chế

Not suitable for hard to machine materials without defined cutting data and stable machine rigidity.
Not intended for high output production where dedicated high performance tooling is required.

Các bước thực hiện

Identify the correct thread designation on the box and confirm it matches the drawing.
Secure the workpiece and mark the drilling location so the tool starts on center.
Drill the hole with the matched Mũi khoan xoắn using suitable cutting fluid.
Deburr the entry so the tap lead can start without edge damage.
Clamp the tap in a stable holder and align it square to the surface.
Start tapping with steady feed and maintain lubrication through the cut.
Reverse out to clear chips when resistance increases and keep the hole clean.
Clean the thread and verify fit with the intended fastener or a gauge.

Phạm vi cung cấp

Cặp mũi khoan taro STANDARD M 6 x 1.0, DIN 371, HSS-E

Đặc tính kỹ thuật

Product type: Mũi taro máy
Thread designation: M 6 x 1.0
Thread system: ISO metric
Standard: DIN 371
Tool material: HSS-E, HSS
Tolerance class: ISO 2 (6H)

Câu hỏi thường gặp (FAQ)

How do you select the correct variant for your drawing Match the thread designation in the product name to the drawing and the mating fastener. Confirm thread series, pitch, and class of fit before you start, especially for inch based threads. Where can you find an overview of the TwinBox concept Use this PDF for orientation and the ring system overview. TwinBox overview as PDF Is this tap suitable for lỗ bít or lỗ thông The suitability depends on flute geometry and lead form noted in the product name. Spiral flute execution is typically chosen for lỗ bít because chips are transported out of the hole. Which TwinBox execution is referenced by the ring term in the product name Use this PDF for the execution specific differentiation and handling notes. Standard TwinBox as PDF Which tolerance class do you typically achieve The typical tolerance class for this execution is ISO 2 (6H) when the process is set up correctly and the hole preparation matches the thread system. Do you need cutting fluid Yes, use suitable cutting fluid for the material to reduce friction and control chip formation. Keep lubrication consistent from start to finish and clean the tool after use. Which tools do you need in addition to the kit You typically need a suitable holder for the tap and a stable drilling setup. Use clamping that keeps the tool axis square to the surface and prevents wobble. Where can you find the VÖLKEL catalog for additional variants and technical context Use the catalog for the full program and selection guidance. VD 23 catalog as PDF

Do you need help selecting or using the product?
Use the biểu mẫu liên hệ.

Thuyết minh kỹ thuật

Loại ren	Ren hệ mét ISO DIN 13
Tiêu chuẩn	DIN 371
Form	Form
Vật liệu	HSS-E
Tolerance	ISO 2 /6H
Kích thước	Nominal diameter D M 6 x 1.0
EAN	4022835377931
Mã hàng	37793