Bàn ren ngoài (tạo ren ngoài) DIN 223 (DIN EN 22568) HSS - M 2.3 x 0.4
You restore or create ren ngoài with a Bàn ren ngoài (tạo ren ngoài) when machine access is limited. The result depends on correct preparation, alignment, and lubrication.
Select the die by the thread designation and standard stated in the product name, then use a suitable die holder to keep the tool square. Use cutting fluid matched to your material and clear chips to protect the thread profile.
- Cut ren ngoài on rods, bolts, and studs in repair, prototyping, and small batch work.
- Use with a Bàn ren ngoài (tạo ren ngoài) holder or Tay quay bàn ren to keep the die square to the workpiece axis.
- Apply cutting fluid matched to your material to reduce friction and protect the thread profile.
- Process: manual driving or assisted driving depending on your holder and machine setup.
- Use: cắt ren, taro lại ren, and làm sạch ren depending on condition.
Lưu ý Confirm thread system, pitch, and fit requirement before cutting. Prepare the workpiece with a clean lead in chamfer.
- Supports repeatable cắt ren in small batches with minimal setup.
- Good access in confined work areas compared with larger machines.
- Easy to clean and store as an individual tool.
- Works well for service tasks when the correct preparation is in place.
Hạn chế
- Performance is limited in very hard or abrasive materials unless a suitable die execution is selected.
- Cycle time is limited for high volume production compared with dedicated machine processes.
- Inspect the workpiece and ensure there is a clean lead in chamfer at the thread start.
- Select a Bàn ren ngoài (tạo ren ngoài) holder and clamp the die securely before you approach the workpiece.
- Apply cutting fluid to the workpiece area and to the die entry side.
- Align the die square to the workpiece axis and start cutting with steady forward pressure.
- Turn the die forward to advance the thread while maintaining alignment.
- Reverse briefly at intervals to clear chips from the cutting edges.
- Continue until the required thread length is reached and then stop the forward feed.
- Back the die off the workpiece and remove it from the holder.
- Clean the die and verify the thread fit with a matching part or a suitable gauge.
- 1 chiếc: tool as specified by the product name
- Product type: Bàn ren ngoài (tạo ren ngoài)
- Standard: DIN EN 22568; DIN 223
- Thread designation: M 2.3 x 0.4
- Thread system: Metric ISO
- Tool material: HSS
- How do you select the correct die for your thread?
- Match the thread designation in the product name to your required ren ngoài and ensure the mating nut or component uses the same system and pitch.
- Which holder should you use for a Bàn ren ngoài (tạo ren ngoài)?
- Use a Bàn ren ngoài (tạo ren ngoài) holder or Tay quay bàn ren that clamps the die securely and supports square alignment to the workpiece axis.
- Which workpiece preparation is important before cutting an ren ngoài?
- Prepare a clean lead in chamfer and ensure the workpiece surface is free of scale and burrs so the die can start square and cut cleanly.
- How do you manage chips during ren ngoài cutting?
- Use suitable cutting fluid and clear chips regularly during the operation so chips do not score the new thread surface.
- Where can you find additional technical information on Bàn ren ngoài (tạo ren ngoài)?
- Use this PDF for background, setup notes, and general guidance: Technical information Bàn ren ngoài (tạo ren ngoài) as PDF
- How do you store and protect a Bàn ren ngoài (tạo ren ngoài) after use?
- Clean the die, remove cutting residue, and apply a light corrosion protection film before storage in a dry container.
- Where can you find more VÖLKEL threading tool information for selection and application?
- Use this catalog for product range and selection help: VD 23 catalog as PDF
Do you need help selecting or using the product?
Use the biểu mẫu liên hệ.
