Bàn ren ngoài (tạo ren ngoài) DIN 223 (DIN EN 22568) HSS - M 30 x 1.5
You cut ren ngoài on rods, bolts, and stud material with a Bàn ren ngoài (tạo ren ngoài). This supports controlled cắt ren in repair and small batch work when the workpiece is prepared correctly.
Match the die to your thread requirement and clamp it securely in a Bàn ren ngoài (tạo ren ngoài) holder. Start square to the workpiece axis and use lubrication to reduce friction and wear.
- Cut ren ngoài on rods, bolts, and studs in repair, prototyping, and small batch work.
- Use with a Bàn ren ngoài (tạo ren ngoài) holder or Tay quay bàn ren to keep the die square to the workpiece axis.
- Apply cutting fluid matched to your material to reduce friction and protect the thread profile.
- Process: manual driving or assisted driving depending on your holder and machine setup.
- Use: cắt ren, taro lại ren, and làm sạch ren depending on condition.
Lưu ý Confirm thread system, pitch, and fit requirement before cutting. Prepare the workpiece with a clean lead in chamfer.
- Compact solution for ren ngoài cutting on prepared stock material.
- Controlled thread fit when you start square and use consistent lubrication.
- Quick tool change when used in a die holder or Tay quay bàn ren.
- Suitable for sửa ren when enough material remains on the workpiece.
Hạn chế
- Performance is limited in very hard or abrasive materials unless a suitable die execution is selected.
- Cycle time is limited for high volume production compared with dedicated machine processes.
- Inspect the workpiece and ensure there is a clean lead in chamfer at the thread start.
- Select a Bàn ren ngoài (tạo ren ngoài) holder and clamp the die securely before you approach the workpiece.
- Apply cutting fluid to the workpiece area and to the die entry side.
- Align the die square to the workpiece axis and start cutting with steady forward pressure.
- Turn the die forward to advance the thread while maintaining alignment.
- Reverse briefly at intervals to clear chips from the cutting edges.
- Continue until the required thread length is reached and then stop the forward feed.
- Back the die off the workpiece and remove it from the holder.
- Clean the die and verify the thread fit with a matching part or a suitable gauge.
- 1 chiếc: tool as specified by the product name
- Product type: Bàn ren ngoài (tạo ren ngoài)
- Standard: DIN EN 22568; DIN 223
- Thread designation: M 30 x 1.5
- Thread system: Metric ISO
- Tool material: HSS
- How do you select the correct die for your thread?
- Match the thread designation in the product name to your required ren ngoài and ensure the mating nut or component uses the same system and pitch.
- Which holder should you use for a Bàn ren ngoài (tạo ren ngoài)?
- Use a Bàn ren ngoài (tạo ren ngoài) holder or Tay quay bàn ren that clamps the die securely and supports square alignment to the workpiece axis.
- Which workpiece preparation is important before cutting an ren ngoài?
- Prepare a clean lead in chamfer and ensure the workpiece surface is free of scale and burrs so the die can start square and cut cleanly.
- How do you manage chips during ren ngoài cutting?
- Use suitable cutting fluid and clear chips regularly during the operation so chips do not score the new thread surface.
- Where can you find additional technical information on Bàn ren ngoài (tạo ren ngoài)?
- Use this PDF for background, setup notes, and general guidance: Technical information Bàn ren ngoài (tạo ren ngoài) as PDF
- How do you store and protect a Bàn ren ngoài (tạo ren ngoài) after use?
- Clean the die, remove cutting residue, and apply a light corrosion protection film before storage in a dry container.
- Where can you find more VÖLKEL threading tool information for selection and application?
- Use this catalog for product range and selection help: VD 23 catalog as PDF
Do you need help selecting or using the product?
Use the biểu mẫu liên hệ.
