Hotline: 098 484 7029 Email: [email protected]
Set sney ulir

Bàn ren lục giác (set of 5 pcs.) DIN standard HSS UNF 1/4 – UNF 1/2

★ 0.0 (0 ulasan)
Terjual: 0
Tampilan: 0
Diimpor dari: Jerman
Asal: Jerman

Bàn ren lục giác (set of 5 pcs.) DIN standard HSS UNF 1/4 – UNF 1/2 VÖLKEL, mã 49540, phù hợp cho gia công ren ngoài.

SKU: 49540
€188,59
Status stok: Backorder 4-8 minggu
Harga indikatif
Deskripsi

Bàn ren lục giác (set of 5 pcs.) DIN standard HSS UNF 1/4 – UNF 1/2

Use this tool when you need reliable thread creation or re-tapping on the shop floor. Correct preparation, alignment, and lubrication are the main practical checkpoints.

UNF identifies Unified National Fine inch threads used where a finer pitch is typical for the same nominal diameter. HSS indicates high speed thép, a common tool material for cắt ren in many steels and non-ferrous alloys.

Ứng dụng

  • Cut or restore ren ngoài on rods, studs, and bolts when machine access is limited.
  • Use a suitable die holder to keep the die square and to apply even feed along the workpiece axis.
  • Use cutting fluid matched to the workpiece material to reduce friction and protect the thread profile.
  • Process: manual driving or assisted driving depending on your holder and machine setup
  • Use: cắt ren, taro lại ren, and làm sạch ren depending on condition

Lưu ý Verify the workpiece preparation before you start and stop if torque increases unexpectedly.

Lợi ích

  • Creates ren ngoài in one setup when you need flexibility on the shop floor.
  • Supports thread restoration on damaged studs and rods if enough base material remains.
  • Works well in repair environments where you can control alignment and lubrication.
  • Allows quick adaptation to different thread designations without machine programming.
Hạn chế
  • ren ngoài cutting is sensitive to alignment and surface preparation.
  • Not suitable for high volume production where a dedicated threading machine is required.

Các bước thực hiện

  1. Prepare the rod end with a chamfer and remove burrs to support a clean thread start.
  2. Clamp the workpiece securely and mark the target thread length for visual control.
  3. Mount the die in a suitable die holder and tighten the retaining screws evenly.
  4. Apply cutting fluid and start the die square to the workpiece axis with steady torque.
  5. Advance with controlled feed and briefly back off when torque rises to clear chips.
  6. Continue until the required thread length is reached, then reverse out completely.
  7. Clean the thread and verify fit with a matching nut or gauge.

Phạm vi cung cấp

  • 5 chiếc Bàn ren lục giác (set of 5 pcs.) DIN standard HSS UNF 1/4 – UNF 1/2

Đặc tính kỹ thuật

  • Tool type: cắt ren die
  • Thread system: UNF
  • Tool material: HSS

Vui lòng dùng biểu mẫu liên hệ.

Ulasan produk

Berdasarkan 0 ulasan
0.0
Keseluruhan
5★ 0
4★ 0
3★ 0
2★ 0
1★ 0

Jadilah yang pertama mengulas “Bàn ren lục giác (set of 5 pcs.) DIN standard HSS UNF 1/4 – UNF 1/2”

🎁 Tulis ulasan untuk mendapatkan 20 poin hadiah — foto +10, video +15.
Kumpulkan poin hadiah untuk menukar hadiah unik dari Minh Khang Vinatools. Masuk
Silakan masuk untuk mengirim ulasan.
Baru dilihat
Belum ada item