Hotline: 098 484 7029 Email: [email protected]
Schneideisensätze

Bàn ren lục giác (set of 5 pcs.) DIN standard HSS UNF 1/4 – UNF 1/2

★ 0.0 (0 Bewertungen)
Verkauft: 0
Aufrufe: 0
Importiert aus: Deutschland
Herkunft: Deutschland

Bàn ren lục giác (set of 5 pcs.) DIN standard HSS UNF 1/4 – UNF 1/2 VÖLKEL, mã 49540, phù hợp cho gia công ren ngoài.

SKU: 49540
188,59 €
Lagerstatus: Nachbestellung 4-8 Wochen
Richtpreis
Beschreibung

Bàn ren lục giác (set of 5 pcs.) DIN standard HSS UNF 1/4 – UNF 1/2

Use this tool when you need reliable thread creation or re-tapping on the shop floor. Correct preparation, alignment, and lubrication are the main practical checkpoints.

UNF identifies Unified National Fine inch threads used where a finer pitch is typical for the same nominal diameter. HSS indicates high speed thép, a common tool material for cắt ren in many steels and non-ferrous alloys.

Ứng dụng

  • Cut or restore ren ngoài on rods, studs, and bolts when machine access is limited.
  • Use a suitable die holder to keep the die square and to apply even feed along the workpiece axis.
  • Use cutting fluid matched to the workpiece material to reduce friction and protect the thread profile.
  • Process: manual driving or assisted driving depending on your holder and machine setup
  • Use: cắt ren, taro lại ren, and làm sạch ren depending on condition

Lưu ý Verify the workpiece preparation before you start and stop if torque increases unexpectedly.

Lợi ích

  • Creates ren ngoài in one setup when you need flexibility on the shop floor.
  • Supports thread restoration on damaged studs and rods if enough base material remains.
  • Works well in repair environments where you can control alignment and lubrication.
  • Allows quick adaptation to different thread designations without machine programming.
Hạn chế
  • ren ngoài cutting is sensitive to alignment and surface preparation.
  • Not suitable for high volume production where a dedicated threading machine is required.

Các bước thực hiện

  1. Prepare the rod end with a chamfer and remove burrs to support a clean thread start.
  2. Clamp the workpiece securely and mark the target thread length for visual control.
  3. Mount the die in a suitable die holder and tighten the retaining screws evenly.
  4. Apply cutting fluid and start the die square to the workpiece axis with steady torque.
  5. Advance with controlled feed and briefly back off when torque rises to clear chips.
  6. Continue until the required thread length is reached, then reverse out completely.
  7. Clean the thread and verify fit with a matching nut or gauge.

Phạm vi cung cấp

  • 5 chiếc Bàn ren lục giác (set of 5 pcs.) DIN standard HSS UNF 1/4 – UNF 1/2

Đặc tính kỹ thuật

  • Tool type: cắt ren die
  • Thread system: UNF
  • Tool material: HSS

Vui lòng dùng biểu mẫu liên hệ.

Produktbewertungen

Basierend auf 0 Bewertungen
0.0
Übersicht
5★ 0
4★ 0
3★ 0
2★ 0
1★ 0

Be the first to review “Bàn ren lục giác (set of 5 pcs.) DIN standard HSS UNF 1/4 – UNF 1/2”

🎁 Schreiben Sie eine Bewertung und erhalten Sie 20 Bonuspunkte — Foto +10, Video +15.
Sammeln Sie Prämienpunkte, um einzigartige Geschenke von Minh Khang Vinatools einzulösen. Anmelden
Bitte anmelden um eine Bewertung abzugeben.
Kürzlich angesehen
Noch keine Artikel